Inclines N gauge

All posts regarding baseboard construction
Post Reply
User avatar
Butch
Posts: 31
Joined: Wed Nov 18, 2020 1:44 pm
Location: Mid-Essex
Contact:

Inclines N gauge

#1

Post by Butch »

Following on from a discussion on my newbie discussion.

On my new (first) baseboard (4 feet wide x 3 feet deep) I wanted a main line running across the back of the board. I was bringing the line round in a curve at each end. one side heading under a road bridge and the other side into a tunnel. Then dropping the track out of view to circle nearer the front of the board and underneath. Thus maintaining the illusion of this being a through service. Underneath at the front I then had points and a second track so I could run one train one way and then one the other etc.

Problem being on this area of board the incline to get the trains below deck is seemingly indefeasibly steep. At the moment I'm making a drop of 55mm over around 570mm track length. That's about 9.6% gradient. This is with a std 50mm batten between the top and bottom decks. To improve things I reckon I could reduce that to 45mm. That would give me just a little under 8% gradient. Next plan would be to prop the whole front of the board up by around half this so as to similarly halve the gradient giving me a bit under 4% which must be getting close to something that might work.

Both the climbs are also curved, between 9" and 12" radius. I guess with a little more binding on the wheels it might make it harder work on the locos but could improve traction.

Anyway, the board is mostly made up so I'll test at each of the proposed phases above and report back.
All N Gauge
User avatar
Steve M
Posts: 1732
Joined: Thu Oct 04, 2018 5:29 pm
Location: Rochester, Kent
Contact:

Re: Inclines N gauge

#2

Post by Steve M »

Any gradient steeper than1:30 simply won’t work and yours, at 1:10 is way too much. Better still you need to be at 1:40 or less.
I’m not a complete idiot, some pieces are missing. ;)
User avatar
IanS
Posts: 589
Joined: Thu Oct 04, 2018 6:19 pm
Location: The Original Washington, UK
Contact:

Re: Inclines N gauge

#3

Post by IanS »

Butch wrote: Sat Nov 21, 2020 8:20 pm To improve things I reckon I could reduce that to 45mm. That would give me just a little under 8% gradient. Next plan would be to prop the whole front of the board up by around half this so as to similarly halve the gradient giving me a bit under 4% which must be getting close to something that might work.
It wouldn't work like that - the incline would still be 8%.

I know the lines in the diagram aren't at 4% and 8%, they're used for illustrative purposes only.
Attachments
incline2.jpg
incline2.jpg (41.09 KiB) Viewed 167 times
User avatar
Steve M
Posts: 1732
Joined: Thu Oct 04, 2018 5:29 pm
Location: Rochester, Kent
Contact:

Re: Inclines N gauge

#4

Post by Steve M »

To put it another way, to raise your track 55mm you would need a slope of 1.65m at 30:1 or 2.2m at 40:1, and even longer if any of the slope is on a curve as curves induce additional drag.
I’m not a complete idiot, some pieces are missing. ;)
User avatar
Butch
Posts: 31
Joined: Wed Nov 18, 2020 1:44 pm
Location: Mid-Essex
Contact:

Re: Inclines N gauge

#5

Post by Butch »

Understood. I've got this far before I started to explore problems in this area, so I'm going to pin down some track and run some experiments (fails to follow simple instruction). I'll report back, and with the results that you'll all be expecting I'm sure.

Plan B is that this line will now not be able to be circular, I'll still loop the line around at each end and bring it to the font each side on a lighter incline (so I can still keep it out of view with additional scenic elements) and just stop the track each side at the front.
All N Gauge
Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests